水中鈣與鎂的測定
➤ 概述
水中鈣和鎂的測定是透過在 pH 8 – 9 下用乙二胺四乙酸 (EDTA) 的鈉鹽滴定來完成的,並使用 鈣電極進行檢測。 分別以 mg/l Ca2+ 和 mg/l Mg2+ 計算結果。
水中鈣與鎂滴定分析
➤ 本測定中使用的儀器及試劑
儀器與配備
自動滴定儀 | TL 7000 or higher |
電極 | Ca 1100 PLH |
電極線 | L 1 A |
參考電極 | B 2920+ |
電極線 | L 1 N |
攪拌器 | TM 235電磁攪拌器 |
其他配備 | 玻璃燒杯 電磁攪拌棒30mm |
試劑
1. | Na2EDTA 0.05 或 0.1 mol/l |
2. | 乙醯丙酮 Acetylacetone |
3. | Tris(hydroxymethyl)-aminomethane (TRIS) |
4. | 蒸餾水 |
5. | L300 電解液 |
➤ 滴定程序
試劑
按照應用說明“EDTA 滴度測定”中的描述進行EDTA 溶液的力價測定。
RIS/乙酰丙酮緩衝液
將 20.4 g TRIS 溶解在水中,加入 12 ml 乙酰丙酮並用水補足至 1.0 升。
清理電極
電極用蒸餾水清洗。 Ca 1100 儲存在清潔、乾燥的環境中,參比電極的儲存使用電解質溶液 L300。
樣品製備
將100.00ml樣品置於150ml燒杯中,添加15ml TRIS/乙酰丙酮緩衝液,然後用Na2EDTA 0.05或0.1mol/l滴定至2個當量點。 第一個等當點對應於樣品的 Ca2+ 含量,第二個等當點對應於樣品的 Mg2+ 含量。 用量應約為5-15毫升。 對於水質非常硬的水樣品,可以減少樣品量,對於水質非常軟的水樣品,可能需要較低濃度的 EDTA 溶液。
Method data | |||
Default method: | Ca and Mg | Minimum holding time: | 5 s |
Method type: | Automatic titration | Maximum holding time: | 12s |
Modus: | Dynamic | Measuring time: | 4 s |
Measured value: | mV | Drift | 3 mV/min |
Measuring speed / drift: | User defined | Max step size: | 0.5 ml |
Initial waiting time: | 0 s | Slope max ml: | 10 |
Dynamic: | flat | Min. step size | 0.05 ml |
Damping: | none | Slope min. ml | 120 |
Pretitration: | off | ||
End value: | off | Titration direction: | decrease |
EQ: | On(1) | Delay time: | 0 s |
Max. titration volume: | 20mL | Slope value | 120 |
Dosing speed: | 100 % | Filling speed | 30 s |
➤ 計算
(EQ1-B) x T x Mca x F1 | |
Result Ca2+ [mg/l] = | ——————————– |
V x F2 |
(EQ2 – EQ1) x T x MMg x F1 | |
Result Mg2+ [mg/l] = | ——————————– |
V x F2 |
B | 0 | Blank value |
EQ1 | Consumption of titrant at first Equivalence point | |
EQ2 | Consumption of titrant at second Equivalence point | |
T | WA | Actual concentration of the titrant |
Mca | 40,08 | Molecular mass of Ca |
MMg | 24,305 | Molecular mass of Mg |
V | man | sample volume [ml] |
F1 | 1000 | Conversion factor |
F2 | 1 | Conversion factor |